Products

Product Selector View our new products

All products below are listed alpha-numeric order. These listed products can be narrowed by using the search filters to the right. These filters cover the following areas:

  • Systems & Assemblies: will list only product allowed for the selected type of system or assembly
  • Product Category: Will only list products in the category chosen
  • Division: Will only list products are for use in that CSI division

Step 1: Select First Filter
Select the first filter to search by. If filter meets searching needs no further search action is needed.

 

Step 2: Select Second Filter (Optional)
If listed products need to be refined further, select another filter from the remaining two to further refine results.

 

Step 3: Select Last Filter (Optional)
If listed products need to be refined further, select final remaining filter to further refine results.

Search by:

Start over

Colorfast Colorants

Parex USA Exclusive colorant system, used in Acylic Finishes and Coatings, Elastomeric Finishes and Coatings and Specialty Finishes.

  • Longer lasting color / Improved fade resistance and UV resistance
  • Bolder Richer color Spectrum
  • Increased water resistivity
  • Improved opacity

Teifs DPR Acrylic Finish

A 100% acrylic-based textured finish. Made with Dirt Pick-Up Resistance (DPR) meaning the surface of the finish hardens and does not soften again under heat. The non-tacky surface provides high resistance to accumulation of dirt, mold, and pollutants. The finish is integrally colored with high quality pigments.

 

Teifs DPR Acrylic Finishes are offered in four textures.

 

* Smooth 0.5 * Swirl 1.5
* Sand 1.0 * Swirl 2.0
* Sand 1.5  

 

Teifs DPR AM (Arena Mejor)

A high grade 100% acrylic-based sand textured finish. Made with Dirt Pick-Up Resistance (DPR) meaning the non-tacky surface provides high resistance to accumulation of dirt, mold, and pollutants. The finish is integrally colored with high quality pigments that adds lasting color and reduces maintenance. If you’re looking for the best Sand Finish, look no further than our DPR AM (Arena Mejor, literally “Sand Best”).

 

Teifs E-Lastic

A 100 percent acrylic-based elastomeric textured finish. Made with DPR (Dirt Pick-up Resistance) chemistry. Is highly flexible: can bridge pre-existing static hairline cracks. Integrally colored with high quality pigments.

 

Teifs E-Lastic Finshes are offered in four textures.

 

* Sand 1.0 * Choice 0.75
* Sand 1.5 * Swirl 1.5

 

TeifsFlex

A 100% acrylic-based textured finish. Integrally colored with high-quality pigments. Exceeds EIMA recommendations and ICC-ES Acceptance Criteria.

 

TeifsFlex Acrylic Finshes are offered in six textures.

 

* Tejas * Tejas Fine
* Piedra * Piedra Grande
* Cuarzo * Freedom

 

Parex USA Metallic Coating

100% acrylic based metallic coating that provides a glossy, metallic appearance.   Economically replicate the look of metal panels with the ease of a coating application. Includes dirt pickup resistance (DPR) which ensures the coating does not soften under head and resists accumulation of dirt, mold, and pollutants.  Available in 12 standard colors and unlimited custom colors.

Parex USA DPR Coating (formerly Teifs Coat Smooth)

A 100% acrylic-based coating. DPR (Dirt Pick-up Resistance): The surface of the coating hardens and does not soften again under heat. The non-tacky surface provides high resistance to accumulation of dirt, mold, and pollutants. Excellent hiding power as well as flexibility and drying characteristics. Mixed on site with water. Integrally colored with high quality pigments.

Parex USA Elastomeric Coating

A 100% acrylic Elastomeric nontextured coating. Highly flexible: can bridge existing hairline cracks. Integrally colored with high quality pigments.

Teifs Base

A base Coat for Teifs EIFS. Adhesive to laminate EPS to listed substrates. Used in a 50% acrylic paste to 50% cement ratio. Requires the addition of portland cement

TeifsBase DB

A base Coat for Teifs EIFS. Adhesive to laminate EPS to listed substrates. Applied without the addition of cement. Mixed on site with water. Excellent workability.

Teifs Wet Base Optimum

A premium basecoat and adhesive with higher than industry average acrylic content. For use in Teifs EIFS. Adhesive to laminate EPS to listed substrates. Used in a 50% acrylic paste to 50% cement ratio. Requires the addition of Portland cement.

Teifs Dry Base Optimum

A basecoat for Teifs EIFS. Adhesive to laminate EPS to listed substrates. Applied without the addition of cement. Mixed on site with water. Best in class workability. Extended pot life.

TeifsBase FR

A fiber reinforced base Coat for Teifs EIFS. Adhesive to laminate EPS to listed substrates. Applied without the addition of cement. Mixed on site with water. Best in class workability. Enhanced strength.

Teifs Adheez

An adhesive to laminate EPS to listed substrates. A 100% acrylic polymer base. Ready to use, applied without the addition of cement. Exceptional workability.

Teifs Structure

A base Coat for Teifs EIFS. Adhesive to bond EPS to listed substrates. A 100% acrylic polymer base. Ready to use, applied without the addition of cement.

Teifs One Coat Concentrate

A fiber reinforced stucco base concentrate. Factory prepared mixture of portland cement, fibers, and proprietary ingredients. Specified sand is added at the job site. Can be installed up to 1/2 in. (12.7mm) in one application.

Teifs One Coat Sanded

A pre-blended fibered, sanded one coat stucco. Factory-blended mix that requires only the addition of water. Can be installed 3/8-1/2 in. (9.5-12.7mm).

Teifs Scratch & Brown Concentrate

A fiber-reinforced factory blended cement scratch and brown coat for use in stucco conforming to ASTM C 926. Factory prepared blend of portland cement, lime, fibers, and proprietary ingredients. Specified sand conforming to ASTM C 897 is added at job site. Can be installed up to 3/8 in. 9.5 mm) thick in one application.

Teifs Scratch & Brown Sanded

A fiber-reinforced factory blended cement scratch and brown coat for use in stucco conforming to ASTM C 926. Factory prepared blend of portland cement, lime, fibers, sand, and proprietary ingredients. Can be installed up to 3/8 in. 9.5 mm) thick in one application.

Parex USA Stucco Level Coat

Surface leveler for use in Teifs Krak-Shield assemblies. Bonds to stucco brown coat. Can be applied in a thin layer. Applied without the addition of cement. Mixed on site with water only. Excellent workability

Parex USA Masonry Veneer EPS Basecoat and Adhesive

EPS Basecoat & Adhesive is the first premium grade basecoat used to adhere and coat EPS continuous insulation sheeting as part of the Parex USA MVS - CI System. This specialized EPS Basecoat creates an energy efficient wall substrate suitable for the application of manufactured masonry veneers or in conjunction with other Parex USA finishes.

Parex USA Carvable Mortar

Parex USA Carvable Mortar is a polymer modified architectural mortar used to create shapes and sculpted structures. It is the ideal product to mimic the look of wood, rock or stones.


Parex USA Carvable Mortar can be build up to 6” in total thickness and can be used over a wide variety of substrates. It can be machine or hand applied and is paintable

Parex USA Sandable Basecoat

A 100% Acrylic sandable basecoat that comes as a gray base. It enhances the appearance and uniformity of smooth finishes. It can be easily recoated with Parex USA Allegro II. Ideal over EIFS basecoats, stucco basecoats, stucco finishes, and interior drywall.

Parex USA Stucco Mesh

4.5 oz fiberglass 38 in. (96.5 cm) mesh. For increased crack reduction and strength. Embed in Stucco Level Coat to smooth and level surface for finish. Use with Krak-Shield and Krak-Master stucco assemblies. Not for use on EIFS.

Parex USA 352 Adhesive Mesh

4.5 oz fiberglass mesh. Self-adhesive, facilitates the wrapping of complex contours. Is alkali-resistant. NOTE: Complex architectural details only.

Parex USA 354 Standard Mesh 4.8oz (Formerly TeifsMesh 4.8 oz)

4.8 oz fiberglass 38 in. (96.5 cm) mesh. Is highly flexible for full walls or details. Is alkali-resistant. Standard reinforcement of Parex USA EIFS walls for impact resistance and details. Required in combination with Parex USA 358.14 High Impact Mesh or 358.20 Ultra High Impact Mesh. May be used in Parex USA Krak-Shield assemblies.

Parex USA 355 4.5oz Mesh

4.5 oz fiberglass 38 in. (96.5 cm) mesh. Is highly flexible for full walls or details. Is alkali-resistant. Standard reinforcement of Parex USA EIFS walls for impact resistance and details. Required in combination with Parex 358.14 High Impact Mesh or 358.20 Ultra High Impact Mesh. May be used in Parex USA Krak-Shield assemblies.

Parex USA 356 Short Detail Mesh

4.5 oz fiberglass mesh 9.5 in. (24 cm) wide. Is highly flexible for use on details and is alkali-resistant. Ideal for use in backwrapping,corners, reveals and trim.

Parex USA 358.10 Intermediate Impact Mesh

12 oz fiberglass 38 in. (96.5 cm) mesh. Is an intermediate strength mesg used to enhance impact and abuse resistance. Is alkali-resistant. Use with Parex USA EIFS to achieve EIMA’s medium impact strength classification. May be used in Parex USA Krak-Shield assembly.

Parex USA 358.14 High Impact Mesh

15 oz fiberglass 38 in. (96.5 cm) mesh. A high strength mesh used to enhance impact and abuse resistance. Is alkali resistant. Use with Parex USA EIFS to achieve EIMA’s high-impact strength classification.

Parex USA 358.20 Ultra High Impact Mesh

20 oz fiberglass 38 in. (96.5 cm) mesh. Is an ultra high strength mesh used to enhance impact and abuse resistance. IS alkali-resistant. Use with Parex USA EIFS to achieve EIMA’s ultra-high impact strength classification.

Parex USA 360 Fast Window Mesh

A preformed mesh used to reinforce the corners of rough openings. It is ready to use and pre-cut for fast installation It should be used in conjunction with Parex USA Weather Tech WRBs: WeatherSeal Spray & Roll-On, WeatherSeal Trowel-On and WeatherBlock SP1 Spray & Roll-On.

Parex USA 360 Fast Windown Mesh comes in boxes of 40 units.

WeatherTech 365 Flashing Tape

365 Flashing Membrane is a high performance tape designed for use with stucco and CI systems to seal around penetrations and at sheathing joints and window/door flanges. It can be applied to most substrates without the use of primer or mechanical fasteners. The polyester fabric top layer provides a excellent bonding surface for cementitious and acrylic finishes.

 

Our Flashing Membrane is offered the following dimensions:

* 6" x 75'

 

Parex USA 369 DrainEdge

Speeds and simplifies application of the WaterMaster systems and assemblies. Eliminates need for pre-wrapping or rasping the back of boards at terminations. Eliminates the need for mineral wool and track at terminations.

WeatherTech 396 Sheathing Tape

Non-woven fabric used to tape the joints of the sheathing boards to which a Parex liquid water-resistive barrier is applied.

 

Our Sheathing Tape is offered in 3 sizes:

* 4" x 500'

* 6" x 500'

* 9" x 500'

Parex USA 600 Clear Sealer

A 100% acrylic transparent coating. Contains EPA-registered mildewcide and algicide. .Dirt resistant. The coating hardens and does not soften under solar heating. The nontacky surface provides high resistance to accumulation of dirt and pollutants. Water vapor permeable.

Parex USA 610 Matte Clear Sealer

A 100% acrylic transparent gloss coating. Contains EPA-registered mildewcide and algicide. Dirt resistant. The coating hardens and does not soften under solar heating. The nontacky surface provides high resistance to accumulation of dirt and pollutants. Water vapor permeable.

Parex USA Accel-Dry

Accel-Dry is an acrylic and elastomeric finish accelerator. Accel-Dry admix is ideal for wet and cold climates as it allows finishes to dry quicker. This is a key feature for jobs that might face inclement weather or need to be completed quickly.

Parex USA Accel-Pak - Rapid Setting Admix

Rapid set admix for any Parex USA polymer modified EIFS Base Coat & Adhesive to reduce set time for Winter weather or quick EIFS patch & repair work.

Parex USA Adacryl Admix & Bonding Agent (formerly Teifs Admix & Bonding Agent)

A 100% acrylic emulsion additive for portland cement based products. Admixture in portland cement based mixes. High-performance acrylic polymer bonding agent.

Parex USA PrimeShield

Is a 100 percent acrylic-based primer that improves the mechanical bond of the finish to the stucco substrate. PrimeShield reduces the chance of efflorescence which may result from the cement content of various bases. It also enhances the appearance and uniformity of the finish. The product is water-vapor permeable and does not create a vapor retarder.

Parex USA Primer

A 100% acrylic-based primer. Reduces the chance of efflorescence which may result from the cement content of various bases. Enhances the appearance and uniformity of the finish. Water-vapor permeable. Does not create a vapor retarder. Improves finish coverage.

Parex USA Pro-Tect

Pro-Tect is a clear water repellant used to protect stucco, masonry and mature concrete from water, enhancing the beauty of cementitious stucco, masonry and mature concrete by improving stain resistance. Pro-Tect maintains the beauty of stucco by reducing susceptibility to freeze-thaw damage, efflorescence, biological growth. Available in both one and five gallons.

Parex USA Quik Cure

Is a water-based acrylic curing membrane formulated to provide excellent performance in the water retention section of ASTM C-309. QuickCure provides a curing membrane over cementitious surfaces allowing finishes to be applied quickly, while protecting against delamination and efflorescence. The product provides a sound, sealed substrate for a uniform finish over either stucco or concrete.

Parex USA Silicone Additive

Provides enhanced UV protection for finishes and coatings to prevent damage from the sun and improves water repellency of any Parex USA or finish.

Parex USA The Plus Advantage

Additional dose of biocide protectant formulated at the manufacturing plant.

Parex USA WeatherTech WeatherFlash

WeatherFlash liquid flashing and joint filler is used to prepare and seal exterior wall rough openings and detail joints as part of the WeatherTech air and water

barrier system

Areas of Use

• Window and door rough openings

• Sheathing joints

• Fastener points

• Wall penetrations (Beams, pipes, utility boxes, etc.)

 

Available in 20 oz. Sausage Packs or 3 Gal Pails

Parex USA WeatherTech WeatherBlock SP1 Spray & Roll-On

A Class I 100% Acrylic co-polymer fast drying vapor barrier, elastomeric waterproof and air barrier coating which can be either rolled, brushed, or spray applied. Is designed for use as vapor barrier behind exterior claddings. Is extremely flexible: can bridge cracks and accommodate small movements up to 1/32 in. (0.8mm). Bridges 1/8 in. (3mm) gaps at sheathing board joints with Parex USA 396 Sheathing Tape embedded.

Parex USA WeatherDry

A Waterproofing Base Coat. Acrylic co-polymer base. Requires the addition of portland cement.

 

VIDEO: View the Parex USA Weatherseal Spray and Roll-On / Trowel-On Video

Parex USA WeatherTech WeatherSeal BG

A Single-component, non-fibrated, asphalt modified, neoprene waterproofing membrane which can be either troweled, rolled, brushed, or spray applied. Designed to provide high-performance below grade protection from positive side water pressure. Allows low levels of moisture vapor to escape to prevent blistering and delamination of the applied membrane while prohibiting infiltration of moisture through foundation walls, footings, retaining walls, planter boxes and between slab. Solvent free formulation incorporate anti-microbial additive to prevent mold and mildew growth.

 

VIDEO: View the Parex USA Weatherseal Spray and Roll-On / Trowel-On Video

Parex USA WeatherTech WeatherSeal SB

A single component cement base waterproofing coating for CMU and concrete. It is a multipurpose polymer modified waterproofing product: Air Barrier, Water Resistive Barrier, and Scratch Coat that can be used above grade and below grade for planters or concrete foundations.

Parex USA WeatherSeal SB is can be used to fill joints in CMU and to level rough concrete or CMU walls.

Parex USA WeatherSeal Spray & Roll-On

A 100% acrylic elastomeric waterproof membrane and air barrier which can be either rolled, brushed, or spray applied. Extremely flexible: can bridge cracks and accommodate small movements up to 1/32 in. (.8mm). Designed for use as water-resistive barrier behind Teifs EIFS or stucco. Birdges 1/4 in. (6 mm) gaps at sheathing board joints with 396 Sheathing Tape embedded.

 

VIDEO: View the Parex USA Weatherseal Spray and Roll-On / Trowel-On Video

Parex USA WeatherSeal Trowel-On

A 100% acrylic based, trowelable water-resistive barrier membrane. Extremely flexible: can bridge existing hairline cracks and accommodate small movements.

 

VIDEO: View the Parex USA Weatherseal Spray and Roll-On / Trowel-On Video